FrontPage
makeSEA windpowerWriter Wind Turbine Parts List
Parts List for windpowerWriter
Below is a list of parts, not 3D printable, for the windpowerWriter. The links provided are suggestions only as some of these may be sourced from other locations.
 | Small and light, DC/DC 0.8-5V to DC 5V Step UP Boost Voltage Converter Power Supply Module DC-DC in 1.5V 2.5V 3V 3.3V |
 | 2500Pcs 50 Values 1R - 10MR 1/4W Resistance 1% Metal Film Resistor Assorted Kit |
 | 100pcs/lot Into the schottky diode SR5100 5A/ 100V DO - 27 SB5100 |
 | The new 0.21 mm enameled wire QA-1-155 Copper 0.21mm http://www.aliexpress.com/item/The-new-0-21-mm-enameled-wire-QA-1-155-Copper-0-21mm/32528712133.html |
 | 10pcs 1x 40 Pin 2.54 mm Right Angle Single Row Pin Header 90 degrees |
 | 1PCS Black Farad Capacitor 2.7V 500F 35x60MM Super Capacitor 60mm DIY New Arrival |
 | 10 pcs 608ZZ 8X22X7 mm Deep groove ball bearing bearing steel 608 2Z |
 | 10pcs NEW A3144 A3144E OH3144E Hall Effect Sensor |
 | 100 pcs 2 Pin Screw blue PCB Terminal Block Connector 5mm Pitch |
 | 1Pcs Mini DC-DC USB 0.9V-5V to 5V Boost Step-up Power Supply Module PFM Control |
 | 2x 3M 20 Gauge AWG Silicone Rubber Wire Cable Red Black Flexible Wonderful Gift |
 | CP2102 USB 2.0 to TTL UART Module 6Pin Serial Converter STC Replace FT232 Module |
 | 5pcs Double Side Copper Prototype PCB Tinned Universal Board Experimental Development Plate 40x60mm 4x6cm |
 | 20pcs N50 Strong Block Cuboid Magnets 30mm x 10mm x 3mm Rare Earth Neodymium |
 | With the bootloader 1pcs pro mini atmega328 Pro Mini 328 Mini ATMEGA328 3.3V/8MHz for Arduino |
 | Openbuilds collar locker OX CNC machine parts Shaft Lock Collar 5mm /8mm - V Slot Linear Extrusion |
 | 10pcs/lot MR105 MR105ZZ MR1052Z Metal Sealed Shielded Miniature Mini Deep Groove Bearing Ball 5x10x4mm 5*10*4 Free Shipping |
 | High Quality 10pcs double Rubber sealing cover deep groove ball bearing 625-2RS 5*16*5 mm 625 RS / 625RS P0/z2 |
 | Lot of 100 X 3mm White LED 18000mcd Free Resistors http://www.aliexpress.com/item/AE-Lot-of-100-X-3mm-White-LED-18000mcd-Free-Resistors/1333004766.html |
 | 100PCS High Quality M8*16*1.2 Flat Brass Washer Gasket/ Copper Washer Gasket |
8904 Views
Check Out the makeSEA Mash Market® for a collection of useful designs related to this Wiki article.
AR as a Reference and Training Tool
Augmented Reality (AR) is poised to bring dramatic changes to everyday life, so its not hard to imagine that it is already impacting the workplace. AR technology dates back to the mid-1990s,...
AR and Your Trade Show Booth
No matter what industry you are in, your trade show booth and the image you present is your show piece and influences the perception others have of your company and brand. In the trade...
Architecture, Design and AR
Recently I made a move to another state and in the process decided to have a small house built rather than rent or buy something I would need to put significant money into immediately. The...
Enhance Your 3D Print Program
As 3D printing is evolving it is pretty much mainstream coursework in institutions of higher learning. The departments of engineering, architecture, fine arts, and medical have incorporated...
Embrace Change
Change can sometimes be difficult and a little intimidating but the use of augmented reality as part of your marketing, sales and even training efforts is rapidly becoming main stream. One...
This is why we share our designs!
We recently heard from Manes Cabanas, Associate Professor at the Universidad de Oviedo in Spain. He has used the makeSEA brushless motor as a teaching tool for his students in Electrical...
makeSEA R&D
makeSEA Proudly Sponsors Construct3D 2018 Conference at Georgia Tech
Is 3D printing good or bad for construction jobs?
Move over Moore . . . there's a new law in town!
3D Printing and the Olympics
Christoph is at it AGAIN!
Innovate
What time is it?!? - Time for the Oct O'Clock!
Halbach Motor Build Kits Are Finally In!
A viable, efficient 3D printed motor? Yes we can.
Exploring magnetic PLA and other 3d printer filaments
Burning up
Heat is an important consideration when working with 3D printable ABS and PTEG materials.
The devil is in the details
When Christoph designed, printed and load tested version 1 (the second version) of the makeSEA brushless motor, he had some concerns about how many RPMs the rotor could sustain without breaking apart.
Why 3D printing will change the world: reason 13
3D printing is unleashing conceptual designs from the minds of students, amatuers, professional 3D designers and engineers worldwide. And that is a good thing. It allows for trial and error and...